|
2.7 ENGINE KIT INCLUDES 4 CYLINDERS + 4 PISTON W/ RINGS TOP END GASKETs. CYLINDERS ON AN EXCHANGE BASIS.
|
 |
AIR FILTER HOUSING USED
|
|
|
BRACKET DISTRIBUTOR
|
|
CHOKE CABLE SWB
|
|
|
CYLINDER HEAD COMPLETE includes Valves and Rockerarms
|
|
ENGINE GASKET SET - This new, not old stock. Becareful when comparison shopping some kits on the market were made over a decade ago. This is a COMP...
|
|
|
ENGINE TIN PROTECTION STRIP PER METER
|
|
Exhaust Stud Nut - YES WE KNOW IT'S BS PRICING FROM THE FACTORY - WE HAVE NOT FOUND AN ALTERNATIVE.
|
|
|
Exhaust Stud Washer
|
|
EXHAUST VALVE
|
|
|
FAN
|
|
FELT AIR CONDUIT Used on the interior surface of the vertical engine tin (7121061072/30) on the rear of the engine
|
|
|
FELT AIR CONDUIT Used on the interior surface of the vertical engine tin (7121061062/30) on the front of the engine.
|
|
GASKET ENGINE OIL FILLER TUBE
|
|
|
Gasket for tappet guide. Gasket for pushrod housing.
|
|
GASKET THERMOSTAT HOUSING
|
|
|
GASKET TIMING COVER
|
|
Intake gasket to carburator - insulator gasket
|
|
|
INTAKE VALVE
|
|
KNOB & CHOKE CABLE WIRE ONLY
|
|
|
LINKAGE CARB PEDAL - PIVOT
|
|
LINKAGE CARB PIVOT - CARB#1
|
|
|
Magnetic drain plug used on the engine, transmission, T-csse, differential and hubs. This is the magnetic plug and should only be used on the drain...
|
|
MOTORMOUNT LH OR RH
|
|
|
OIL DIPSTICK
|
|
OIL DIP STICK TUBE
|
|
|
OIL SCRAPER RING 92MM
|
|
O-RING DIPSTICK TUBE & PUSH ROD TUBE
|
|
|
O-RING THERMOSTAT
|
|
PISTON RING SECOND 92MM
|
|
|
PISTON WITH RINGS 92.5MM
|
|
PISTON WITH RINGS 92MM USED
|
|
|
Push Rod Tube
|
|
ROCKERARM EXHAUST VALVE
|
|
|
RUBBER BOOT AIR INTAKE
|
|
RUBBER MOUNT STARTER
|
|
|
Seal Crank shaft Front. Radial Seal Ring Steyr Original seal. Not aftermarket replacement
|
|
SEAL CRANKSHAFT REAR 75x95x10 Steyr factory original seal. Not aftermarket
|
|
|
SEAL FAN HOUSING ENGINE. Helps maximize air flow to the rear of the engine.
|
|
SEAL INTAKE VALVE - Sold Individually
|
|
|
SEAL PUSHROD TUBE
|
|
SEAL RING AIR INTAKE
|
|
|
SEAL RING AIR INTAKE SMALLER VERSION FITS INTO THE AIR INTAKE
|
|
SEAL RING OIL COOLER
|
|
|
SHAFT/ADVANCE FOR DISTRIBUTOR
|
|
SPRING PUSHROD TUBE
|
|
|
THROWER CRANKSHAFT
|
|
VALVE COVER CYL # 3 USED
|
|
|
VALVE SEAT EXHAUST
|
|
VALVE SEAT INTAKE
|
|
|
VALVE SPRING INTAKE/EXHAUST
|
|
WASHER PUSHROD TUBE
|
|
|
Specific to the Pinzgauer. These are manufactured with the rubber seal
|
|
